Paints are used to decorate as well as provide protection to the interior and exterior of the house. It is a low-cost solution to refresh the looks of the building. It prevents wear and tear in the walls and protects them from the extreme weather conditions prolonging the life of your house. Every paint is different in terms of looks and quality. They have different lives and deterioration, but sometimes, paint failures occur right after the paint job. Such issues pop out due to several factors. The most common of these problems, their causes, and their solutions are discussed in this article.
Blistering of paint happens when air or other fluid is filled between the surface and the layer of paint. The presence of bubbles is the main symptom of such painting failures. If a problem like this is not treated on time, bubbles of paint will expand and burst after some time, leaving the surface exposed to the outer environment.
Causes: The leading cause of these problems includes moisture or heat in the surface or between different layers of paint.
Solution: First, you need to identify which element of the atmosphere is causing this problem. Scrap the bubbles of paint with sandpaper. Apply a layer of primer to fill the porous surface through which moistures build up between the layers. Make sure that the temperature of the surface is below 90 Fahrenheit. Choose high-quality paint to repaint the surface.
Alligatoring of paint is identified by cracks on the surface of the paint. The pattern of cracking or peeling of paint resembles a reptile skin or skin of an alligator. This problem can start at any part of the house but is usually seen in exterior paint. To prevent such failures from happening, always hire the best exterior painting services in Arlington TX.
Causes: Alligatoring can happen by several things, including applying a second coat of paint on an undried first coat, applying a rigid substance like alkyd enamel on a flexible one like a latex primer.
Solution: The only solution to this problem is removing all the paint by scraping from the whole surface where alligatoring has happened. While you are repainting, let the first coat of the paint completely dried. Only then should you paint the second coat on it.
Sagging of paint can be identified as the drooping movement of paint, which happens immediately after the paint application, resulting in the uneven paint coating. It usually occurs when a very thick or thin layer of dye is applied on verticle or inclined surfaces.
Causes: Applying too many coats of paints over one another, painting over a glossy surface that doesn’t provide sufficient tooth for the paint to bond, getting the paint job done by an inexperienced painter who mixes the paint and thinner in the wrong proportion, and applying paint in cold and humid weather.
Solution: Always hire experienced painters in Arlington Texas. Sand the glossy surface to make it rough before applying paint. Avoid painting in cold and humid weather. Sand the surface of the paint where sagging has happened and apply a new coat. Make sure to mix the thinner and dye in appropriate proportion.
This failure can easily be identified by the appearance of white deposits on the surface of bricks, concrete and other masonry materials when they are exposed to moisture. These crystal deposits keep growing over time and cause adhesion problems if not removed before applying new paint.
Causes: Efflorescence happens when excessive moisture escape from the inside of the walls. If the surface was not prepared properly before painting or the previous salt deposits were not cleaned, it can also cause efflorescence on new paint.
Solution: Remove the white deposits with a wire brush. Ensure to wash the surface with one part of phosphoric acid to seven parts of water. Let the surface completely dry. Apply a high-quality primer that can hold back the efflorescence. Apply acrylic paint on the primer to get the premium finish.
Chalking is defined as the formation of fine powder on the surface of the paint. Nearly chalking happens in every painting, but high-quality paint chalks mildly. If too much chalking happens, it poses lots of problems for repainting the same surface. This failure causes the color of the paint to fade away over time. Always seek the help of reliable painters in Arlington Texas, to prevent your paint from chalking.
Causes: The leading causes of the chalking of paint are not sealing the porous surface properly, overexposure of a painted surface to sunlight, using low-quality paint, and use of too much thinner.
Solution: First, you have to determine the extent of chalking, then use pressure washing or sandblasting to remove the deposits of chalking. Let the surface thoroughly dry, and then apply a high-quality primer to seal the porous surface. Always use acrylic paints because they have less tendency to chalk.
The peeling of paint is identified by the formation of flakes on the surface of the paint. This kind of failure is usually seen in the interiors of the house. It happens by using low-quality paint or paint job done by non-professional painters who don’t know which paint combination is good in adhering with each other. Moisture can also play a significant part in the peeling of paint.
Causes: It is mainly caused by not preparing the surface properly for painting. The presence of dirt and dust on the surface causes the paint to peel off. Other causes include the existence of moisture which lowers the binding ability of a paint.
Solution: Clean the surface on which peeling of paint has occurred. Apply a primer to prevent moisture from being built inside the layers. Remove any loose flakes and sand the surface to make it smooth. Hire top-notch interior painting services in Arlington TX, apply new paint coats, and blend with the old paint.